Celerons (PPGA) 2x500@??? HELP
Celerons (PPGA) 2x500@??? HELP
Before does two, I had 1x366 (550), It works PERFECT!
But now I can't Overclock thoes!?
When I reset (save and Exit y/n "Y") the BP6 just freezes (The monitor is Black) until a remove the Battery It can't start.
What shall I do???
What Values shall I Use???
Which BIOS shall I Use???
PLEASE HELP
Nothing is impossible!!!
-
- Board Admin
- Posts: 1395
- Joined: Wed Jul 24, 2002 7:39 am
- Location: Lincoln, NE USA
- Contact:
And Both has the same Stepping ( SL3FY )
FV524RX500
128 SL3FY
MALAY
L1110368-0022 (L1110368-0038)
M C '98
SD-RAM:
* HYUNDAI 256 MB PC133
* 128 MB (MADE IN USA) PC133
HDD:
It was MAXTOR 40GB 7200 2MB(In burned-220V);
Next will be SEAGATE 120 GB 7200 2MB;
VGA:
MATROX G550 (for some time was G400)
Sound:
Yamaha 724 PCI;
LAN:
3COM 905 100/10;
Macronix 100/10;
Power Suply:
"JNC" 230W;
If you need more just say.
At the moment the MB is in a box, 27 Dec 2003 the power suply break and let 220 to ALL (2xHDD burned, 1 chip ot BP6 burned but was repaired)
Now I'm rebuilding the Machine.
Please help me to make it even better.
FV524RX500
128 SL3FY
MALAY
L1110368-0022 (L1110368-0038)
M C '98
SD-RAM:
* HYUNDAI 256 MB PC133
* 128 MB (MADE IN USA) PC133
HDD:
It was MAXTOR 40GB 7200 2MB(In burned-220V);
Next will be SEAGATE 120 GB 7200 2MB;
VGA:
MATROX G550 (for some time was G400)
Sound:
Yamaha 724 PCI;
LAN:
3COM 905 100/10;
Macronix 100/10;
Power Suply:
"JNC" 230W;
If you need more just say.
At the moment the MB is in a box, 27 Dec 2003 the power suply break and let 220 to ALL (2xHDD burned, 1 chip ot BP6 burned but was repaired)
Now I'm rebuilding the Machine.
Please help me to make it even better.
Nothing is impossible!!!
What´s the lowest FSB setting above 66 Mhz? 75? That would mean 7,5 x 75 = 562,5 Mhz. It is not unlikely that you can´t overclock your 500´s that far. Usually 600 Mhz is the absolute limit, but you might have had bad luck.
BP6, RU BIOS, XP SP3, ACPI, 2x366@523(1,95V), Pentalpha HS + 1x 12cm fan @5V, 768MB, Powercolor Geforce 3, RTL8139D NIC, Terratec EWS64L, Samsung M40 80GB (2,5''), LiteOn CDRW
Wait... the slowest FSB setting above 66 is 72, right? So if you overclock it, you run the cpus at 7,5x72=540 Mhz minimum. That might be too much, at least in SMP mode. I´ve had three 366´s combos and none of them was perfectly stable at 550 Mhz. My current cpus would do 550 and 600 Mhz in single mode, but in SMP mode they are only stable at 523. Your cores might just not go to 540 Mhz.
BP6, RU BIOS, XP SP3, ACPI, 2x366@523(1,95V), Pentalpha HS + 1x 12cm fan @5V, 768MB, Powercolor Geforce 3, RTL8139D NIC, Terratec EWS64L, Samsung M40 80GB (2,5''), LiteOn CDRW
ok
i have 2 celeron 500's they are currently running at 584MHZ
they are very unstable anywhere above that
i have 2 celeron 500's they are currently running at 584MHZ
they are very unstable anywhere above that
!!! WARNING !!!
The following forums: www.bp6.com
are infected with the following VIRUS(s): Kuun.infected.all.posts.Win2K.user
The following IRC servers has been exploited: irc.bp6.com
with the Following Exploit: Kuun.lurks.using.mIRC.v5.82.exploit
The following forums: www.bp6.com
are infected with the following VIRUS(s): Kuun.infected.all.posts.Win2K.user
The following IRC servers has been exploited: irc.bp6.com
with the Following Exploit: Kuun.lurks.using.mIRC.v5.82.exploit
Since being repaired has the BP6 booted all the way into the OS.haronix wrote:27 Dec 2003 the power suply break and let 220 to ALL (2xHDD burned, 1 chip ot BP6 burned but was repaired)
If not there may be damage you can't detect.
By the way,
do you still have the 366s. I want to trade from 500s down to 333s or 366s so the FSB can be pushed to 100mhz. It doesn't make sence to stay at 66 or 72FSB when 100 or faster is available.
David