One CPU is 5-10 degrees hotter than the other CPU -Why?

Frequently asked questions about the BP6.

Moderator: hyperspace

Post Reply
hyperspace
Board Admin
Posts: 1395
Joined: Wed Jul 24, 2002 7:39 am
Location: Lincoln, NE USA
Contact:

One CPU is 5-10 degrees hotter than the other CPU -Why?

Post by hyperspace »

One CPU is 5-10 degrees hotter than the other CPU -Why?

This is somewhat normal for this motherboard. Many users have reported similar differences. Replacing existing CPU coolers with more efficient CPU coolers will help.

Reference:
Golden Orb Article

Important Tip:

When you install your CPUs, ensure you get an accurate temperature reading by bending the probes slightly so that they protrude marginally above the socket. Then when you put the CPUs in, the probes will be touching the hot part of the chips. Also, a dab of silicone thermal compound on the probes' contact areas. Can't do any harm.

I have done this on my BP6 and the temps are always within one degree of each other.

The following information comes from InactiveX. Excellent tip! Thanx, InactiveX.
kuun
Post-O-Matic
Posts: 1566
Joined: Sat Nov 02, 2002 5:26 pm
Location: Tennessee
Contact:

Post by kuun »

another tip

check and make sure that the cpu core voltages are the same

if they are not and the hotter CPU has a higher voltage, you have bad caps or caps that are going bad.

Kuun
!!! WARNING !!!
The following forums: www.bp6.com
are infected with the following VIRUS(s): Kuun.infected.all.posts.Win2K.user

The following IRC servers has been exploited: irc.bp6.com
with the Following Exploit: Kuun.lurks.using.mIRC.v5.82.exploit
Dave Rave
G'Day Mate!
Posts: 894
Joined: Thu Sep 26, 2002 4:28 am
Location: Sydney Australia
Contact:

Re: One CPU is 5-10 degrees hotter than the other CPU -Why?

Post by Dave Rave »

This is somewhat normal for this motherboard. Many users have reported similar differences. Replacing existing CPU coolers with more efficient CPU coolers will help.
my 466's were always different temps, running around 47 and 54 degrees no matter which socket or fan arrangement

I recently bought some opportune new fand, 6500rpms, and they are both now even at 36degrees
go figure
bp6's 3 x dual @ 533
. . . . 1 x dual @ 466
. . . . 1 sngl @ 400
[( 2 x dual xeon 2.4ghz )]
[( 2 x dual xeon 2.66ghz )]
[( 1 x 2.4C ghz )]
[( 1 x 2.4B ghz )]
[( 1 x dual AMD 1800MP )]
[( 1 x P4 1600 )]
[( 1 x 500 ppga )]
3 x piii 866
Dave Rave
G'Day Mate!
Posts: 894
Joined: Thu Sep 26, 2002 4:28 am
Location: Sydney Australia
Contact:

Post by Dave Rave »

the MBM will show 'a' cpu voltage and the also important VTT 1.50 v rail

if you set the voltage configuration type to be Abit BP6, then the VTT box will show the cpu 1 core voltage.

after you are happy that it is showing correctly, set it back, as it is important to know the 1.50v is staying steady. when it varies, it shows your EC10 capacitor may need changing
bp6's 3 x dual @ 533
. . . . 1 x dual @ 466
. . . . 1 sngl @ 400
[( 2 x dual xeon 2.4ghz )]
[( 2 x dual xeon 2.66ghz )]
[( 1 x 2.4C ghz )]
[( 1 x 2.4B ghz )]
[( 1 x dual AMD 1800MP )]
[( 1 x P4 1600 )]
[( 1 x 500 ppga )]
3 x piii 866
Dave Rave
G'Day Mate!
Posts: 894
Joined: Thu Sep 26, 2002 4:28 am
Location: Sydney Australia
Contact:

Post by Dave Rave »

the third fan 'hookup' is next to the ide plugs in the far corner
kuun
Post-O-Matic
Posts: 1566
Joined: Sat Nov 02, 2002 5:26 pm
Location: Tennessee
Contact:

Post by kuun »

hmm

i had that problem once

go into the settings and set it to fan1

see what happens
!!! WARNING !!!
The following forums: www.bp6.com
are infected with the following VIRUS(s): Kuun.infected.all.posts.Win2K.user

The following IRC servers has been exploited: irc.bp6.com
with the Following Exploit: Kuun.lurks.using.mIRC.v5.82.exploit
Derek
Site Admin
Posts: 2489
Joined: Tue Jul 23, 2002 3:55 pm
Location: Canada
Contact:

Post by Derek »

Fan power header #3 (farthest from the CPUs) does not monitor the RPMs.

Also, to clarify the VTT voltage readout confusion: If you set MBM “standard”, CORE 2 will read as your VTT voltage. If you set it to BP6, CORE 2 will read as the CPU CORE voltage.
-Derek
kuun
Post-O-Matic
Posts: 1566
Joined: Sat Nov 02, 2002 5:26 pm
Location: Tennessee
Contact:

Post by kuun »

66-ac yeah i meant to change the fan settings for all fans see if you got a reading anywhere

i've never used the fan header 3 so im not sure what it can do
!!! WARNING !!!
The following forums: www.bp6.com
are infected with the following VIRUS(s): Kuun.infected.all.posts.Win2K.user

The following IRC servers has been exploited: irc.bp6.com
with the Following Exploit: Kuun.lurks.using.mIRC.v5.82.exploit
24seven
IRC Lurker
Posts: 495
Joined: Wed Jul 24, 2002 5:23 pm
Location: Derbyshire UK
Contact:

Post by 24seven »

From what I remember it is not possible to get a reading from fan header #3.

I think the winbond chip will only moniter two fans.
Dave Rave
G'Day Mate!
Posts: 894
Joined: Thu Sep 26, 2002 4:28 am
Location: Sydney Australia
Contact:

Post by Dave Rave »

User Manual Page 2 - 7

Fan 1/2/3
The FAN 3 speed can't be monitored by the system and can't be turned off.
======

must be Alex at MBM who coded the Winbond with fan 1 2 & 3
or maybe it's just the BP6 that didn't bother implementing
bp6's 3 x dual @ 533
. . . . 1 x dual @ 466
. . . . 1 sngl @ 400
[( 2 x dual xeon 2.4ghz )]
[( 2 x dual xeon 2.66ghz )]
[( 1 x 2.4C ghz )]
[( 1 x 2.4B ghz )]
[( 1 x dual AMD 1800MP )]
[( 1 x P4 1600 )]
[( 1 x 500 ppga )]
3 x piii 866
Dave Rave
G'Day Mate!
Posts: 894
Joined: Thu Sep 26, 2002 4:28 am
Location: Sydney Australia
Contact:

Post by Dave Rave »

User Manual Page 2 - 7

Fan 1/2/3
The FAN 3 speed can't be monitored by the system and can't be turned off.
======

must be Alex at MBM who coded the Winbond with fan 1 2 & 3
or maybe it's just the BP6 that didn't bother implementing
Post Reply