WinXP only "sees" one CPU on BP6

OS / Drivers / BIOS
Post Reply
marqus
Posts: 15
Joined: Sat Aug 27, 2005 2:56 pm

WinXP only "sees" one CPU on BP6

Post by marqus »

Hi,

i got my BP6 running with two cellys 533, but WinXP Pro only shows one CPU.
What do i have to do? The Boards works fine and the CPUs are ok. Any ideas?

thx,
markus
Dave Rave
G'Day Mate!
Posts: 894
Joined: Thu Sep 26, 2002 4:28 am
Location: Sydney Australia
Contact:

Post by Dave Rave »

when it's booting, make sure it shows two cpus on the post screen.
on the PCI list mem show post screen, there will be two lots of 128mb memory under cpu cache

XP Pro or Home ? Home is good for one cpu

did you have two cpus when you installed XP ?
or add it in later ?

where are you looking that it only shows one cpu ?
device manager should show
Computer - ACPI Multiprocessor
maybe the other non ACPI multiprocessor
bp6's 3 x dual @ 533
. . . . 1 x dual @ 466
. . . . 1 sngl @ 400
[( 2 x dual xeon 2.4ghz )]
[( 2 x dual xeon 2.66ghz )]
[( 1 x 2.4C ghz )]
[( 1 x 2.4B ghz )]
[( 1 x dual AMD 1800MP )]
[( 1 x P4 1600 )]
[( 1 x 500 ppga )]
3 x piii 866
marqus
Posts: 15
Joined: Sat Aug 27, 2005 2:56 pm

Post by marqus »

Hi,

hm, when i check the booting screen, sometimes its 2 cpu, sometimes only one...AARGH, is my BP6 dead?
I installed XP Pro as "Standard PC" by pressing F5 during install beginning. May this be the problem? I see only one CPU in devicemanager or taskmanager (there should be 2 different diagrams, one for each CPU).

any ideas?

thx
Dave Rave
G'Day Mate!
Posts: 894
Joined: Thu Sep 26, 2002 4:28 am
Location: Sydney Australia
Contact:

Post by Dave Rave »

if you installed when it booted as only one cpu, it's gonna be a uniprocessor

r u overclocking ?
too little voltage will often show one cpu not present.

if not, plain 533 celeron, at least 1.85v.
if it's iffy, use 1.90v

what does computer type show in device manager ?
my friends notebook shows
Advanced Configuration and Power Interface (ACPI) PC under XP Home notebook
my dual HT Xeon shows
ACPI Multiprocessor PC under XP Pro
marqus
Posts: 15
Joined: Sat Aug 27, 2005 2:56 pm

Post by marqus »

Hey,

i reinstalled the system. without pressing F5 this time. Now there are 2 CPUs. Dunno what the problem was.
BUT: When running the MultiMedia benchmark with Sandra Lite 2005 it shows only one FPU (1xFPU). Comparing with an Dual P3 500 (4xFPU???) the BP6 Combo scores VERY low (1400 vs 7000 I think).

Is this, because the BP6 only emulates DUAl CPU? Will I gain perfomance after all in this combo? Cause i want to run a gameserver.

thx
purrkur
Linux Guru
Posts: 687
Joined: Fri Dec 12, 2003 5:57 pm
Location: Sweden
Contact:

Post by purrkur »

marqus wrote:Hey,

i reinstalled the system. without pressing F5 this time. Now there are 2 CPUs. Dunno what the problem was.
BUT: When running the MultiMedia benchmark with Sandra Lite 2005 it shows only one FPU (1xFPU). Comparing with an Dual P3 500 (4xFPU???) the BP6 Combo scores VERY low (1400 vs 7000 I think).
I don't have Sandra specifics in my head but I am sure that Sandra activates stuff like SSE which you have in the P3 but not in the Cellies. You also have a 100 or 133MHz FSB on the P3 but only 66 on the BP6 which has been shown to be a performance killer if your BP6 is doing more than just raw CPU intensive stuff.
marqus wrote:Is this, because the BP6 only emulates DUAl CPU? Will I gain perfomance after all in this combo? Cause i want to run a gameserver
Emulates dual CPU :)

The BP6 is a real dual CPU but it has some limitations and can definitely be considered the poor mans dual cpu motherboard. I would say that your software isn't reporting things correctly, and I am positive that your dual 500MHz P3 does not have 4 FPU's (although that might be emulated as well :D ).

As for using the machine as a gameserver, I would advise against it. All games use only a single CPU so running it as a game server would be practically like using it like a single CPU machine. The Celerons weren't cut out for that kind of action.
2x533MHz@544MHz, 2.0V
640MB PC100 memory
Realtek RTL-8139 NIC
Maxtor 6Y080L0 80GB hdd
Debian Linux stable with 2.4.8 kernel
Post Reply