POST displays incorrect proc. MHz values

Post Reply
ReD-BaRoN2
Posts: 13
Joined: Wed Jan 25, 2006 11:53 am

POST displays incorrect proc. MHz values

Post by ReD-BaRoN2 »

Hi,

I'm overclocking my BP6 with dual 500MHz cel. Upon post, it only displays certain resultant frequencies as follows:

7.5 mult. @ 66 fsb POST displays 500 (ok)
7.5 mult. @ 72 fsb POST displays 533 (ok)
7.5 mult. @ 75 fsb POST displays 563 (ok)
7.5 mult. @ 78 fsb POST displays 550 (should be ~585)
7.5 mult. @ 80 fsb POST displays 600 (ok)
7.5 mult. @ 82 fsb POST displays 600 (should be ~615)
7.5 mult. @ 84 fsb POST displays 600 (should be ~630)
7.5 mult. @ 85 fsb POST displays 600 (should be ~637)
7.5 mult. @ 86 fsb POST displays 600 (should be ~645)
7.5 mult. @ 87 fsb POST displays 650 (ok)
7.5 mult. @ 88 fsb POST displays 650 (should be ~660)
7.5 mult. @ 89 fsb POST displays 650 (should be ~667)
7.5 mult. @ 90 fsb POST displays 650 (should be ~675)
7.5 mult. @ 91 fsb POST displays 650 (should be ~682)
7.5 mult. @ 92 fsb POST displays 650 (should be ~690)
7.5 mult. @ 93 fsb POST displays 650 (should be ~697)
7.5 mult. @ 94 fsb POST displays 700 (ok)
7.5 mult. @ 95 fsb POST displays 713 (ok)
7.5 mult. @ 96 fsb POST displays 700 (should be ~720)

What's the deal with that? I'm running the latest BIOS from the download page, but I was also on an earlier BIOS rev. that did the same thing.

Thanks!
Dave Rave
G'Day Mate!
Posts: 894
Joined: Thu Sep 26, 2002 4:28 am
Location: Sydney Australia
Contact:

Post by Dave Rave »

It's a BIOS display thing. wouldn't worry about it.
MBM will show the 'correct' speed in windows.

plus, you will be hard to get a useable stable system much past 78 FSB without serious cooling.
Last edited by Dave Rave on Thu Jan 26, 2006 12:20 pm, edited 1 time in total.
ReD-BaRoN2
Posts: 13
Joined: Wed Jan 25, 2006 11:53 am

Post by ReD-BaRoN2 »

Thanks Dave!
purrkur
Linux Guru
Posts: 687
Joined: Fri Dec 12, 2003 5:57 pm
Location: Sweden
Contact:

Post by purrkur »

BIOS doesn't measure the speed. It goes by a pre-programmed table. It won't reflect your actual speed so it can be safely ignored just like Dave Rave so correctly pointed out.
2x533MHz@544MHz, 2.0V
640MB PC100 memory
Realtek RTL-8139 NIC
Maxtor 6Y080L0 80GB hdd
Debian Linux stable with 2.4.8 kernel
KliK
Posts: 350
Joined: Fri Mar 11, 2005 3:56 pm
Location: Zagreb, Croatia
Contact:

Post by KliK »

what is the highest speed that you can boot the system with?! :D
ReD-BaRoN2
Posts: 13
Joined: Wed Jan 25, 2006 11:53 am

Post by ReD-BaRoN2 »

I haven't even put an OS on it yet, so I don't know what speed it will realistically run at, but I am surprised at how high it will POST. That being said, one of the procs dropped at 600 or so, but the other one keeps taking the abuse ;).
KliK
Posts: 350
Joined: Fri Mar 11, 2005 3:56 pm
Location: Zagreb, Croatia
Contact:

Post by KliK »

ReD-BaRoN2 wrote:I haven't even put an OS on it yet, so I don't know what speed it will realistically run at, but I am surprised at how high it will POST. That being said, one of the procs dropped at 600 or so, but the other one keeps taking the abuse ;).
that might be the power suplly...but just up the voltage!!! i'm curious to see which speed will boot?! 'cause the post is idle CPU power, and boot is stressing it more than 100% CPU load in OS!!!

post the results...
headseed
Posts: 165
Joined: Thu Dec 26, 2002 5:45 pm

Post by headseed »

if you don't feel like installing an OS right away, or maybe don't have the hard drive ready yet to do so, why don't you see if it will boot Knoppix or some other flavor of live linux? Then you may know if it is somewhat stable.

If you use bittorrent and have a relatively fast connection, you can download the whole .ISO in under an hour.

Good luck with the OC!
Dual Barton Mobile 1.8ghz
Venice 3000+ @ 2.6ghz
lots of BP6s and two VP6s all apart currently
ReD-BaRoN2
Posts: 13
Joined: Wed Jan 25, 2006 11:53 am

Post by ReD-BaRoN2 »

I'm going to be installing Gentoo Linux on it over the weekend. Given that Gentoo builds most of itself from source, that should be a good judge of the procs ability.
purrkur
Linux Guru
Posts: 687
Joined: Fri Dec 12, 2003 5:57 pm
Location: Sweden
Contact:

Post by purrkur »

ReD-BaRoN2 wrote:I'm going to be installing Gentoo Linux on it over the weekend. Given that Gentoo builds most of itself from source, that should be a good judge of the procs ability.
I am a Gentoo user myself but I haven't bothered with the BP6 and Gentoo because it would take too long :) However, Debian runs nice on the BP6.
2x533MHz@544MHz, 2.0V
640MB PC100 memory
Realtek RTL-8139 NIC
Maxtor 6Y080L0 80GB hdd
Debian Linux stable with 2.4.8 kernel
ReD-BaRoN2
Posts: 13
Joined: Wed Jan 25, 2006 11:53 am

Post by ReD-BaRoN2 »

Gentoo rocks!

I've been running Gentoo from a stage 1 install on a Pentium 200 for a couple years! Talk about a long install time ;). That being said, it was just a fileserver/home gateway, i.e. no x-windows. So post install performance wasn't that big of a deal.
purrkur
Linux Guru
Posts: 687
Joined: Fri Dec 12, 2003 5:57 pm
Location: Sweden
Contact:

Post by purrkur »

ReD-BaRoN2 wrote:Gentoo rocks!

I've been running Gentoo from a stage 1 install on a Pentium 200 for a couple years! Talk about a long install time ;). That being said, it was just a fileserver/home gateway, i.e. no x-windows. So post install performance wasn't that big of a deal.
Hehehe! I agree, if you got the time then why not?

Anyway, if you like Gentoo and you would like something similar without the compile then try out Arch Linux (www.archlinux.org). Not as big but a very helpful and enthusiastic community and a great distro with a good, own-built package manager.
2x533MHz@544MHz, 2.0V
640MB PC100 memory
Realtek RTL-8139 NIC
Maxtor 6Y080L0 80GB hdd
Debian Linux stable with 2.4.8 kernel
ReD-BaRoN2
Posts: 13
Joined: Wed Jan 25, 2006 11:53 am

Post by ReD-BaRoN2 »

Thanks for the pointer, I'll check it out.
Post Reply